Dialogic DSI SS7MD Manual do Utilizador Página 138
- Página / 176
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
138
Chapter 7 Configuration Overview
7.2.2 High Speed Signaling Links Configuration
The Signaling Gateway supports HSL in accordance with ITU Q.703 Annex A. Two HSL links are configurable
on a Dialogic
®
DSI SS7HDP Network Interface Board using processor (EQU) values of x-1 or x-33 (x is the
board position).
The timeslot on the C7SLx TS parameter must be set to 0 for a HSL link, that is the timeslot for a HSL link
must be set to x-y-0 (x is the board position, y is the PCM value).
Only an HSL link can be configured on an unstructured PCM, and a T1 HSL link must be received on the same
board as it is processed. Additionally, an SS7 link cannot be changed from HSL to LSL or from LSL to HSL. A
timeslot (TS) can only be associated with a structured HSL link if it is not associated with a signaling link,
cross connect, monitoring or circuit group.
The following commands demonstrate HSL board, PCM and signaling link configuration.
cnboi:bpos=1,brdtype=ss7hdp-64-4,sigtype=ss7;
cnpci:pcm=1-1,pcmtype=e1,ff=uns;
cnpci:pcm=1-2,pcmtype=e1;
c7lsi:ls=1,nc=1,opc=10,dpc=20,ni=2,lssize=2,ss7md=itu14;
c7sli:c7link=1,equ=1-1,ts=1-1-0,ls=1,slc=0,m56k=0,hsl=y;
c7sli:c7link=2,equ=1-33,ts=1-2-0,ls=1,slc=1,m56k=0,hsl=y;
7.2.3 SS7 M2PA Operation
The Signaling Gateway is capable of replacing TDM SS7 links with signaling links operating over IP providing
the equivalent functionality to MTP layer 2 by using the SIGTRAN M2PA protocol. Typically M2PA signaling
links would be used when the Signaling Gateway is either offering longhaul over IP operation between two
SEPs, or when two Signaling Gateways are acting as a single Point Code and the inter Signaling Gateway SS7
link is provided by M2PA over IP.
For M2PA operation, rather than associating an EQU or TS with an SS7 signaling link (C7LINK), the SS7 link
is instead associated with a SIGTRAN link (SNLINK) defined to be of type M2PA. The SIGTRAN link is used to
identify a SCTP Association as being used for M2PA operation.
Figure 7. M2PA Example
Figure 7 shows an example of a Signaling Gateway connected to a SEP on the TDM side and a SEP on the IP
side.
Example MML for the SIGTRAN M2PA part of the above configuration is:
SNSLI:SNLINK=1,SNTYPE=M2PA,END=C,IPADDR=194.192.185.11,
HPORT=3565,PPORT=3565,LABEL=SEP2-1;
SNSLI:SNLINK=2,SNTYPE=M2PA,END=C,IPADDR=194.192.185.11,
HPORT=3566,PPORT=3566,LABEL=SEP2-2;
C7LSI:LS=2,OPC=3,DPC=2,LSSIZE=2,SS7MD=ITU14,NC=1,NI=2;
C7SLI:C7LINK=3,SNLINK=1,LS=2,SLC=0;
C7SLI:C7LINK=4,SNLINK=2,LS=2,SLC=1;
C7RTI:C7RT=2,NC=1,DPC=2,LS1=2;
SG
PC3
SEP
PC 1
SEP
PC 2
193.145.185.151
193.145.185.154
IP
Signaling
TDM
Signaling
- Dialogic 1
- DSI Signaling Servers 1
- Copyright and Legal Notice 2
- Publication Date: August 2008 2
- Document Number: 05-2304-005 2
- Contents 3
- Revision History 8
- Chapter 1: Overview 9
- Chapter 1 Overview 10
- Chapter 2: Specification 17
- 2.3.2 Dialogic 19
- Chapter 2 Specification 20
- Chapter 4: Operation 27
- Chapter 4 Operation 28
- Are you sure? [Y/N] 29
- CNSYS:SECURE=Y; 31
- 5.3.2 MTP3-Specific Timers 47
- Table 6. MTP3 ITU Timers 47
- Table 7. MTP3 ANSI Timers 47
- ALCLS:CLA=,CODE=…; 50
- ALCLS:CLA=3,CODE=20; 50
- ALCLP[:CLA=]; 50
- CNMOI:C7LINK=,STS=,RTS=; 58
- CNMOE:C7LINK=; 58
- CNMOE:C7LINK=1; 58
- CNPCC:PCM=1-1,SYNCPRI=3; 62
- CNPCE:PCM=; 62
- CNPCE:PCM=1-1; 62
- • The RDC is blocked 64
- OFFSET value to take effect 70
- CNUSC:USER=3,AUTH=SHA; 75
- CNUSE:USER=; 75
- CNUSE:USER=3; 75
- CNXCI:OTS=,ITS=,[DUPLEX=]; 77
- CNXCE:OTS=,[DUPLEX=,]; 77
- CNXCE:OTS=1-1-16; 77
- C7LSE:LS=; 80
- C7LSE:LS=1; 80
- C7RTC:C7RT=1,NC=1,LS1=2; 82
- C7RTE:C7RT=,NC=; 82
- C7RTE:C7RT=1,NC=1; 82
- IPEPS:ETH=1,SPEED=100; 86
- IPEPS:ETH=4,IPADDR=STANDBY2; 86
- • MMPTP - MML Port Print 89
- • MMLOP - MML Log Off Print 89
- • MMLOS - MML Log Off Set 89
- • MMPTC - MML Port Change 89
- Attributes 91
- Examples 91
- Output Format 91
- Chapter 6 Command Definitions 100
- RDC1=1,LABEL=ALARM; 102
- RDCRE:RECORD=,[DISCARD=Y]; 103
- RDCRE:RECORD=1; 103
- SGDPI:DEST=1, RAS=1; 108
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 108
- SGDPI:DEST=,RAS=,[LABEL=,]; 108
- SGDPC:DEST=1, RAS=1; 109
- SGDPE:DEST=; 109
- SGDPE:DEST=1; 109
- SGDPP:[DEST=]; 109
- SGIRC:IR=1,DEST=5; 111
- SGIRE:IR=; 111
- SGIRE:IR=1; 111
- SGIRP:[IR=]; 111
- SNALI:RAS=,SEQ=,SNLINK=; 114
- SNALI:RAS=1,SEQ=1,SNLINK=1; 114
- SNRAE:RAS=; 116
- SNRAE:RAS=1; 116
- IPADDR2=192.112.111.123;; 119
- SNSLC:SNLINK=1, PPORT=2905; 120
- SNSLE:SNLINK=; 120
- SNSLE:SNLINK=1; 120
- STIPP:IPADDR=173.132.23.3; 128
- IP Status 128
- EXECUTED 128
- • Status 133
- • Stratum 133
- • Offset 133
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=2,RTPRI=MTP; 141
- • itself 143
- • an IP address of 0.0.0.0 143
- 194.192.185.11 145
- 192.195.185.11 145
- 192.195.185.12 145
- 194.192.185.12 145
- RESET=Y,LABEL=C7LINK; 158
- RDPDE:REPORT=1,C7LINK=3; 158
- 194.192.185.111 166
- 195.193.185.12 167
- 195.193.185.11 167
- 195.193.185.111 167
- 11.3.2 SG 2 Configuration 168
- STTPP command 169
- Chapter 13: Command Summary 171
- Chapter 13 Command Summary 172
- Glossary 175
- Chapter 14 Glossary 176
Manuais e produtos relacionados com Redes Dialogic DSI SS7MD
Redes Dialogic Mitel SX-2000 Especificações
(26 páginas)
(26 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais